NC Pumps | Fountain Pumps

Fountain Pro
PondMaster
Rio
Via Aqua

NC Pumps carries a large selection of pumps for almost any water pumping application. We have fountain pumps from four different manufacturers. Whether you are building a tabletop fountain, repairing that garden fountain that the previous owners left in disrepair, or constructing an artistic wall fountain with a waterfall, NC Pumps has the pump that you are looking for. Our pump charts are organized by GPH or Maximum Head to make it easier for you to shop for your pump. If you would prefer to shop by brand, that is also available.

PondMaster fountain pumps range in size from 250 GPH to 4000 GPH. The maximum head (height to which a pump is able to move water) ranges from 6' to 18'. These quality pumps are very reliable. More Info...

PM2
250 GPH

Suitable for small to medium size garden fountains, piped statuary, and ponds, the PondMaster PM2 is a 250 GPH Submersible Pump with a 1/2 inch MNPT discharge and 1/2 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord and operates submerged or in-line consuming a maximum of 24 Watts. A ceramic shaft and foam pre-filter are included. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 3 Year Limited Manufacturer's Warranty. More Info...

Service and Maintenance: Periodically the pump will need to be cleaned when the flow slows down or stops. To clean, unplug and remove from water. Slide off pre-filter cover and wash out foam pre-filter pad. After repeated washing, the foam will need to be replaced. After a period of time, deposits may build up inside the pump cover. Remove the four screws which hold the pump cover to the motor housing. The impellor is the only serviceable item. It can be pulled out and cleaned. If it is worn or broken the entire impeller assembly can be replaced. This will restore the pump to original capacity. Do not over tighten screws during reassembly. Check that O-ring is seated into grove in pump cover. If pump fails to start, recheck that impellor is not blocked by debris. For best results the minimum water level depth should be 2 inches. Pumps taken out of service with the fluid inside run the risk of forming a crust which may prevent subsequent start. The pump should be flushed out with fresh water. Always check cord for sharp bends which can cause premature cracking. Do not lift the pump with the cord. Running the pump in chlorine or bleach solution is not recommended. Do not allow the pump to run dry.

PM3
350 GPH

Suitable for small to medium size garden fountains, piped statuary, and ponds, the PondMaster PM3 is a 350 GPH Submersible Pump with a 1/2 inch MNPT discharge and 1/2 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord and operates submerged or in-line consuming a maximum of 35 Watts. A ceramic shaft and foam pre-filter are included. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 3 Year Limited Manufacturer's Warranty. More Info...

PM5
500 GPH

Suitable for small to medium size garden fountains, piped statuary, and ponds, the PondMaster PM5 is a 500 GPH Submersible Pump with a 1/2 inch MNPT discharge and 1/2 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord and operates submerged or in-line consuming a maximum of 45 Watts. A ceramic shaft and foam pre-filter are included. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 3 Year Limited Manufacturer's Warranty. More Info...

PM7
700 GPH

Suitable for small to medium size garden fountains, piped statuary, and ponds, the PondMaster PM7 is a 700 GPH Submersible Pump with a 1/2 inch MNPT discharge and 1/2 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord and operates submerged or in-line consuming a maximum of 60 Watts. A ceramic shaft and foam pre-filter are included. Pump Measurements: 5 in. x 3.8 in. x 4.2 in. 3 Year Limited Manufacturer's Warranty. More Info...

PM9.5
950 GPH

Suitable for large size garden fountains, piped statuary, and ponds, the PM9.5 is a 950 GPH Submersible Pump with a 3/4 inch MNPT discharge and 3/4 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord, plastic finned pre-filter for greater flow through and operates submerged or in-line consuming a maximum of 93 Watts. Its ceramic shaft helps make it very strong. Pump Measurements: 5.5 in. x 3.4 in. x 5 in. 3 Year Limited Manufacturer's Warranty. More Info...

PM12
1200 GPH

Suitable for large size garden fountains, piped statuary, and ponds, the PM12 is a 1200 GPH Submersible Pump with a 3/4 inch MNPT discharge and 3/4 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord, plastic finned pre-filter for greater flow through and operates submerged or in-line consuming a maximum of 135 Watts. Its ceramic shaft helps make it very strong. Pump Measurements: 5.5 in. x 3.4 in. x 5 in. 3 Year Limited Manufacturer's Warranty. More Info...

PM18
1800 GPH

Suitable for large size garden fountains, piped statuary, and ponds, the PM18 is a 1800 GPH Submersible Pump with a 3/4 inch MNPT discharge and 3/4 inch FNPT Intake. It has a 120V with 18' 3-prong grounded power cord, plastic finned pre-filter for greater flow through and operates submerged or in-line consuming a maximum of 145 Watts. Its ceramic shaft helps make it very strong. Pump Measurements: 5.5 in. x 3.4 in. x 5in. 3 Year Limited Manufacturer's Warranty. More Info...

2000 HY-DRIVE
2100 GPH

This high-capacity pump is designed specifically for use in larger pond installations. This highly efficient unit, featuring reliable ceramic bearings, delivers up to 2100GPH of water flow for your waterfall. This is enough to create a dynamic, attractive waterfall or drive a medium to large in-pond skimmer. The maximum height for this pump is 13.4 ft.

FEATURES
• Low energy use
• Specifically designed for use with skimmers and waterfalls
• NEW Powerful, efficient magnetic/direct drive motor
• Fish safe because no oil is used
• Continuous duty operation
• Submersible/Inline operation
• Includes extra-large clog-resistant filter screen
• 3/4", 1", 1/1/4" and 1-1/2" barb fittings supplied
• Extra long 25' power cord with grounded plug
• 1 Year warranty
• More Info...

PROLINE HY-DRIVE 2600 WATERFALL PUMP
2600 GPH

This high-capacity pump is designed specifically for use in larger pond installations. This highly efficient unit, featuring reliable ceramic bearings, delivers up to 2600GPH of water flow for your waterfall. This is enough to create a dynamic, attractive waterfall or drive a medium to large in-pond skimmer. The maximum height for this pump is 25 ft.

FEATURES
• Low energy use
• Specifically designed for use with skimmers and waterfalls
• NEW Powerful, efficient magnetic/direct drive motor
• Fish safe because no oil is used
• Continuous duty operation
• Submersible/Inline Operation
• Includes extra-large clog-resistant filter screen
• 1 1/4" Inlet and Outlet
• 3/4"and 1" barb fittings supplied
• Extra long 20' power cord with grounded plug
• 1 Year warranty
• More Info...

3000 HY-DRIVE
3100 GPH

This high-capacity pump is designed specifically for use in larger pond installations. This highly efficient unit, featuring reliable ceramic bearings, delivers up to 3100 GPH of water flow for your waterfall. This is enough to create a dynamic, attractive waterfall or drive a medium to large in-pond skimmer. The maximum height for this pump is 18 ft.

FEATURES
• Low energy use
• Specifically designed for use with skimmers and waterfalls
• NEW Powerful, efficient magnetic/direct drive motor
• Fish safe because no oil is used
• Continuous duty operation
• Submersible/Inline Operation
• Includes extra-large clog-resistant filter screen
• 3/4, 1, 1/14 and 1-1/2" barb fittings supplied
• Extra long 25' power cord with grounded plug
• 1 Year warranty
• More Info...

PRO 3200-XP HY-DRIVE
3200 GPH

This high-capacity pump is designed specifically for use in larger pond installations. This highly efficient unit, featuring reliable ceramic bearings, delivers up to 3200 GPH of water flow for your waterfall. This is enough to create a dynamic, attractive waterfall or drive a medium to large in-pond skimmer and aquariums. The maximum height for this pump is 15 ft.

FEATURES
• Low energy use
• Specifically designed for use with skimmers and waterfalls
• NEW Powerful, efficient magnetic/direct drive motor
• Fish safe because no oil is used
• Continuous duty operation
• Submersible/Inline Operation
• Includes extra-large clog-resistant filter screen
• Back flow check valve and 1-1/2" fittings supplied
• Extra long 20' power cord with grounded plug
• 1 Year warranty
• More Info...

PRO 4000-XP HY-DRIVE
4000 GPH

This high-capacity pump is designed specifically for use in larger pond and aquarium installations. This highly efficient unit, featuring reliable ceramic bearings, delivers up to 4000 GPH of water flow for your waterfall. This is enough to create a dynamic, attractive waterfall or drive a medium to large in-pond skimmer and aquariums. The maximum height for this pump is 17 ft.

FEATURES
• Low energy use
• Specifically designed for use with skimmers and waterfalls
• NEW Powerful, efficient magnetic/direct drive motor
• Fish safe because no oil is used
• Continuous duty operation
• Submersible/Inline Operation
• Includes extra-large clog-resistant filter screen
• Back flow check valve and 1-1/2" fittings supplied
• Extra long 20' power cord with grounded plug
• 1 Year warranty
• More Info...